piwik image

Dixon® B29 DXN B29 | Tipco Technologies <!-- This is title -->

Dixon® B29

Dixon® Boss™ B29 Zinc-Plated Iron 4-Bolt Clamp, 2 in

  • Manufacturers: Dixon
  • Brand Name: Dixon®
  • Tipco Part No: DXN B29
  • MPN: B29
  • Min. Order Qty: 1
  • Qty. Interval: 1
  • Register to see Availability

Dixon® Boss™ 4-Bolt Clamp, Nominal Size: 2 in, 3-4/64 in Maximum Clamp Diameter, 2-48/64 in Minimum Clamp Diameter, Locking Style: Bolt, Torque Rating: 60 ft-lb, Iron, Finish: Zinc-Plated, 450 deg F Steam Service

California residents see Prop 65 WARNINGS

Product Type      :      Bolt Clamp
Nominal Size      :      2 in
Maximum Clamp Diameter      :      3-4/64 in
Minimum Clamp Diameter      :      2-48/64 in
Locking Style      :      Bolt
Torque Rating      :      60 ft-lb
Material      :      Iron
Finish      :      Zinc-Plated
Temperature Rating      :      450 deg F Steam Service
  • 4-bolt type clamp with two gripping fingers and two clamp sections
  • Bolts in boss clamps are designed to bend as they are tightened, this allows the clamp to conform to the hose outside diameter
  • Always tighten bolts to their specified torque value
  • Periodic re-tightening of bolts is required due to "cold flow" phenomenon present in all rubber hoses
  • Recommended for steam service up to 450 deg F

Instructions:

  • 4-Bolt Dixon® Boss™ clamp bolt tightening sequence, using a torque wrench, begin tightening the bolts as follows: A) Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) one full turn.
  • B) Front bolt (bolt with nut facing assembler that is closest to gripping finger) one full turn.
  • C) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
  • D) Opposite side back bolt (bolt with nut facing assembler furthest away from gripping finger) one full turn.
  • E) Opposite side front bolt (bolt with nut facing assembler closest to gripping finger) one full turn.
  • F) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
  • G) Repeat above procedure "a" through "f" until all of the bolts have reached the recommended torque.
  • H) Remove assembly from vise.

Safety Notes:

  • The bolts used in the Boss™ interlocking clamps are not standard bolts.
  • They vary from standard bolts in their length, diameter, overall thread length and material hardness.
  • These bolts can be retorqued, but it is not recommended that the bolts or clamps be reused, as they are designed for a single bend only.
  • Dixon® recommends using only factory supplied replacement bolts.
  • Replacement nuts and bolts are available, contact Dixon® for more information.
  • Torque values for clamps are based on dry bolts.
  • The use of lubricant on bolts will adversely effect clamp performance.
  • Do not lubricate nuts and bolts.
  • Recommended torque rating in ft-lb.
  • Worn-out hose couplings can be dangerous.
  • They should be checked regularly and replace when necessary.
  • Each coupling user should review applications and add safety devices where indicated.
  • Note: Pressurized steam is an extremely dangerous commodity.
  • Only hose, fittings, clamps and accessory items that have been approved for steam service should ever be used!
  • Never use an unapproved item for steam service.
  • Always follow the manufacturer's product recommendations for pressurized steam handling.
  • video https:www.youtube.com/embed/opJzyrWzvjw
  • video https:www.youtube.com/embed/wYrt27WXkqY
  • video https:www.youtube.com/embed/NuQJUieHqHo
  • video https:www.youtube.com/embed/ggXtciMvaWU